Daily

Comet 650R Ignition Coil + Spark Plug Replacement

한국어로 읽기 →
Comet 650R Ignition Coil + Spark Plug Replacement
Finally~~ I fixed my busted Comet

Had a hard time tracking down an ignition coil T_T Went for a ride for the first time in almost a week.

Comet 650R Ignition Coil + Spark Plug Replacement
Ignition coils were hard to find, and while looking into this and that I ended up getting two. The one on the left is an ignition coil for the 250R (injection), and the one on the right is an ignition coil for the 650R carb model

But really, an ignition coil does the same job either way.. and the 250R and 650R are compatible, so I bought both.

The left one is 33410HN9110 and
the right one is 33430HN9110. But looking at it, the right one turned out to be for the front cylinder.. It can still be fitted, but the length is different.
The one fitted to the front cylinder has a longer wiring lead.

The one that was on there before is 33410HN9120.

Comet 650R Ignition Coil + Spark Plug Replacement
Since the ignition wasn’t working properly, I figured carbon deposits might have built up on the plug, so this is the spark plug I ordered along with it.

Comet 650R Ignition Coil + Spark Plug Replacement
Comet 650R Ignition Coil + Spark Plug Replacement
Reusing photos I posted the other day..haha Open the main seat and loosen the bolt holding the fuel tank in place

In my case I didn’t remove the fuel tank, I just held it up with one hand while working. Last time I tried to remove the tank for no good reason and broke the fuel pump, which cost me an undeserved 80,000 won heh heh heh

And of course I’d just come from the gas station with a full tank, so it was ridiculously heavy =_=

Comet 650R Ignition Coil + Spark Plug Replacement
I lifted the fuel tank, undid two bolts with a 7mm? or 8mm socket, then pulled it out to the side like that and set the tank down to work.

Just pop the two wires off, pop pop, and plug them back in, pop pop.

When reassembling the bolts, you need to fit a ring-shaped wire at the front along with them. You can see it in the photo

Comet 650R Ignition Coil + Spark Plug Replacement
Comet 650R Ignition Coil + Spark Plug Replacement
haha Last time I tried pulling the spark plug with the wrench, only managed to unscrew it and it wouldn’t come out, so after tasting failure.. I used tape haha

After unscrewing it all the way, I stuck tape on like in the right photo, wedged it in and pulled, and it popped right out. Yesss. Felt like digging out a stubborn bit of earwax

Put in the new spark plug and tighten it.

For torque, when fitting a new one, turn it by hand and then another 1/2 turn with the wrench.
When refitting an existing plug after cleaning, turn it 1/8 turn further. It’s in the manual!

Oh, and when cleaning the plug it’s good to check the gap too.
The manual lists the gap as 0.8~0.9mm
Personally, my way of checking is to just pull out a card, and if it wedges in, it’s right..haha

Well, assembly is the reverse of disassembly..

Tried starting it, no FI light and it starts right up
The rpm is sitting around 1800 since it hasn’t warmed up yet hehe

I was so excited I geared up and went for a ride for the first time in ages heh

Comet 650R Ignition Coil + Spark Plug Replacement
When I got back, Mango was like this..

Comet 650R Ignition Coil + Spark Plug Replacement
And Guava is like this

Now that the two of them are friends, they don’t even greet people when they come home haha bad kids..just because they’ve got a friend now..

Anyway, that’s it for today’s maintenance log!!

Related

Leave a comment