This is something I posted on the cafe I’m active in when I did the start button DIY, and since it came to mind, just in case~
I’ve moved it over to my blog.
You never know when it might be needed~ and there might be people looking for it heh
ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ
First, the product I installed is
I bought it here. My car is a September ’08 Transform, without an immobilizer.
I’m not certain whether the wiring is the same as the older NF, so please check before you work on it.
That module is a product with start button + remote start functions built in.
Refer to this post to learn how to use it and what it does.
And if there’s one problem,
since it uses the stock remote, you can’t remote start from very far away, like from an underground parking garage.
And on my car, the remote doesn’t work once the engine is running.
But after a remote start (with the remote not working), if nobody opens a door within a certain time, the car locks the doors on its own. So you have to open the door with the key,,
and the moment you unlock with the key and open the door, the alarm goes off ;;
Mine doesn’t have a siren sound so only the blinkers flash, but cars with a working siren could be loud..
I’m still using it fine, but it’s something to consider if you’re thinking of buying.
If you don’t need the remote start function, I think you can look for and buy a module without it. I’ve seen the same product as a module without that function.
At the end of this post there’s a section on wiring a line for key detection,
and after doing that work, I confirmed that when the engine is started it detects the key and does not lock the doors automatically.
The problem is that it’s weak on security, and I think you’ll have to take that into account.
If you can make the remote work even after the engine is started, I think that would solve the problem.
I park in the yard in front of my house, so nobody’s going to steal it, and it doesn’t get in the way of my use.
It’s a simple job where you just tap into the wiring, so I only took a few photos, and I’ll go through it with photos and explanations.
Also, there are plenty of posts on the cafe about removing the cover under the steering wheel / removing the door trim, so I won’t explain those separately.
This is the manual that comes with the purchase.
The 6 wires coming out on the right are thick wires,
and the 5 wires on the left are thin wires.
The wires on the right are the main wiring, and the start button only works once all of them are connected,
while among the wires on the left, some are needed and some are unnecessary.
I’ll explain in more detail below.

First of all, since there’s a steering lock by default, the steering lock is the type that only releases when the key is inserted and turned, regardless of current.
You can hear a clunk as it locks when you turn the key and pull it out.
So get a copy key or something made, cut it with a cutter, grip it with long-nose pliers, insert it, and leave it in either the acc / on position, whichever.
This is the start button that connects to the module. After removing the cover underneath, spread the retaining pins on the back as in the photo and mount it.
The module and the start button are separate; don’t connect the wire in advance, pass it through that hole first and then connect it to the module.
Once plugged in it’s hard to pull out..

From here the wiring work begins.
Behind the key cylinder there should be a connector shaped like that. First you have to disconnect it from the key cylinder. (It operates while unplugged)
If for some reason the start button doesn’t work, you can plug that connector back in and turn the key to start the engine.
Looking at the connector layout from the wire side toward the plug side,
–
– – –
1 2 3
6 5 4
– – –
if we call it that,
No. 1 is yellow – starter motor -> product yellow
No. 2 is pink – constant power (12v) -> product red
No. 3 is white – IG2 -> product brown
No. 4 is blue – IG1 -> product white
No. 6 is green – ACC output -> product blue
And the product’s black wire goes to chassis ground. (Just loosen a screw on a metal panel or the like and wedge it in)
That’s it. This refers to the product’s thick wires, and I think you’ll understand better if you look at the manual.
With that, all the thick wires are done.
Now the thin wires remain.
To briefly explain the thin wires –
The brown wire, I’m not exactly sure what it’s used for, but there’s no problem at all if you don’t connect it. Even looking at the manual, no idea what it’s saying..
The green wire is the one that automatically locks the doors after a remote start, but on my Sonata, if nobody opens a door within a certain time after the doors unlock, it relocks them on its own anyway. So it’s a wire you don’t need to connect.
The white wire is the brake + wire. The engine only starts when you press the brake and push the start button. Without pressing it, it cycles ACC-ON-OFF.
The black wire is the parking brake – wire. It’s a wire that only allows remote start when the parking brake is engaged,
but automatic cars, unlike manuals, only start in park or neutral, so it’s meaningless anyway. So just ground it.
The
red wire is the door unlock detection wire; it’s the wire that starts the engine when 3 door unlock signals come in within 5 seconds.

If you look above the brake pedal, there’s a connector that looks like that. Among its wires there’s a green wire, and that’s the brake wire.
I couldn’t be bothered to strip the insulation, so I just pulled the connector, stuck the wire into that pin, and plugged the connector back in. Works fine.

This photo is the driver’s side front door trim, and in that bundle of wires there, the white wire is the door unlock wire. Strip the insulation here and splice your wire onto it.
Routing the wire into the cabin looks clean if you run it through the rubber boot,
but I already had a lot of wires and couldn’t be bothered, so I ran it on the outside where it’s visible.haha
With this, the start button work is done~
Pressing the start button without pressing the brake cycles ACC – ON – OFF in that order
Pressing the start button with the brake pressed starts the engine immediately.
To turn off the engine, you also have to press the brake and push the button.
With the remote,
door unlock – lock – unlock – lock – unlock (3 unlock signals)
done within 5 seconds triggers remote start
This is something extra I did, and it’s possible if your car has the same function as mine.
I’m not sure whether the older NF has it too, so if you let me know I’ll update the post.
Originally, when I pulled out the key, my car would clunk as the steering lock engaged and all 4 doors would automatically unlock,
and if the tail lights were left on, they’d stay on and then turn off by themselves when the driver’s door was opened.
But due to the nature of the start button, the key stays inserted, so I lost the functions described above,
and losing functions I’d always had was quite inconvenient. I had to unlock the doors myself too..
So what I found is the key detection wire. I didn’t take separate photos, so here’s a link.. I’ll delete it if it’s a problem.
If you look at the photos there, there’s a photo of a pink wire being cut, and the connector under the key cylinder has a wire just like that.
The pink wire is the key detection wire; when the key is inserted, it sends + power toward the connector. And when the key is pulled out, no current flows.
After cutting it as in the photo, (leave the connector side long to make the work easier)
strip the insulation on the connector-side wire and connect it to the wire bringing ACC power from the fuse. (The photo I posted shows it connected)
Done this way, when you press the button once, ACC power comes on and the key is recognized. You hear the ding-ding sound too.
Also, when you turn off the engine after driving, ACC power turns off at the end and the doors unlock automatically.
That’s all! Thanks for reading this long post.
Questions ! I don’t check messages often, so please leave a comment and I’ll reply once I see it!heh