AFM 7.10.1 GENERAL – Consumers
Consumers
The individual consumers (e.g. radio, electrical fuel transfer pump, position lights, etc.) are connected to the appropriate bus via automatic circuit breakers.
Designations and abbreviations used to identify the circuit breakers are explained in Section 1.5 – DEFINITIONS AND ABBREVIATIONS.
Voltmeter
The voltmeter shows the voltage of the essential bus. Under normal operating conditions the alternator voltage is shown, otherwise it is the voltage of the main battery.
Ammeter
The ammeter displays the intensity of current /which is supplied to the electrical system by the alternator, including the current for battery charging.
Landing and Taxi Lights
Landing and taxi lights are built into the left wing, and are each operated by means of a switch (LANDING, TAXI) on the row of switches on the instrument panel.
Position and Strobe Lights
Combined position and strobe lights (anti collision lights) are installed on both wing tips. Each system is operated by a switch (POSITION, STROBE) on the row of switched on the instrument panel.
Flood Light
A two-dimensional light emitter is mounted above the instrument panel. It illuminates the instrument panel as well as all levers, switches, etc. With a rotary button (FLOOD) in the left-hand section of the instrument panel the flood light is switched on and its brightness is adjusted.
Instrument Lighting
With a rotary button (INSTRUMENT) in the left-hand section of the instrument panel the internal lighting of the instruments is switched on and its brightness is adjusted.
Pitot Heating
The Pitot probe, which provides measurement for the Pitot-static system, is electrically heated. The heating is activated with a switch (PITOT) on the row of switches on the instrument panel. The temperature is automatically kept constant by means of a thermal switch on the Pitot probe, and as an additional safety measure a thermal fuse is built in. If this thermal fuse is activated, the Pitot heating can no longer be switched on. PITOT FAIL on the G1000 (if installed) or PITOT on the White Wire annunciator panel (if installed) will be displayed, if the thermal fuse or the thermal switch is activated and the PITOT HT is set to ON. The PITOT HT OFF indication on the G1000 (if installed) is on if the Pitot heating is switched off.
전력 소비 시스템
각각의 전력 소비 시스템들(예; 라디오, 연료 트랜스퍼 펌프, 포지션 라이트 등등.)은 회로 자동차단기(automatic circuit breakers)를 거쳐 각각의 해당 버스에 연결해 준다.
회로 차단기에 사용되는 명칭 및 약어는 Section 1.5 – DEFINITIONS AND ABBREVIATIONS 에 설명되어 있다.
전압계
전압계는 essential 버스의 전압을 보여준다. 정상적인 상황에서는 발전기의 전압 또는 메인 배터리의 전압을 보여준다.
전류계
전류계는 발전기로부터 전력을 공급받는 전기 시스템, 배터리 충전을 위한 전류의 강도를 표시해준다.
랜딩, 택시 라이트
랜딩, 택시 라이트는 왼쪽 날개에 조립되어 있으며 각각 계기 패널에 있는 랜딩, 택시 스위치를 통해 작동된다.
포지션, 스트로브(섬광) 라이트
결합된 포지션, 스트로브 라이트(충돌방지등)는 양 날개 끝에 장착되어 있다. 각 시스템은 계기 패널에 있는 포지션, 스트로브 스위치에 의해 작동된다.
실내등
2차원의 평평한 면의 라이트가 계기 패널 위에 장착되어 있다. 이는 계기 패널을 비춰주고, 마찬가지로 모든 레버, 스위치 등을 비춰준다. 계기 패널 왼쪽 부분에 회전방식의 FLOOD 버튼이 있는데 ON 한 후 밝기를 필요에 따라 조절할 수 있다.
계기 라이트
계기 패널 왼쪽 부분에 회전방식의 INSTRUMENT 버튼이 있는데 계기의 내부를 비춰준다. 스위치를 ON 한 후 밝기를 필요에 따라 조절할 수 있다.
피토 가열(난방)
피토 스태틱 시스템을 위해 측정값을 제공하는 피토관 탐침(pitot probe)은 전기적으로 가열된다. 계기 패널에 위치한 PITOT 스위치를 조작하면 가열할 수 있다. 피토관 탐침에 의해 온도가 자동으로 유지되고, 안전을 위해 추가적으로 온도퓨즈가 내장되어 있다. 만약 온도퓨즈가 작동되면 피토 가열 스위치는 ON 에 있으면 안된다. PITOT FAIL 이 G1000에 나타나거나(장착되어 있을 경우) PITOT 이 White Wire annunciator panel(장착되어 있을 경우)에 나타난다면, 온도 퓨즈나 온도 스위치가 동작하고 있는데 피토 가열 스위치가 ON에 있는 경우이다. 피토 가열 스위치를 OFF 하면 PITOT HT OFF이 G1000(장착되어 있을 경우) 위에 표시된다.