E6-B 4~15p
한국어로 읽기 →Instructions for Using ASA Flight Computer
Your ASA E6-B Flight Computer has two main parts: a circular slide rule side for making quick calculations, and a wind side for computing ground speed and wind correction angle. The slide portion of the circular slide rule side also includes quick-reference material.
ASA Flight Computer User Instructions
The ASA E6-B flight computer has two main parts: a circular slide rule for quick calculations, and a wind side for computing ground speed and the wind correction angle. The sliding part of the circular slide rule also includes quick-reference tables.
The Slide Rule Side
The term “circular slide rule” shouldn’t be intimidating. This side of your computer simply consists of a rotating disk with numbers on the middle scale, which when set against similar numbers on the fixed portion ( outer scale), allows you to solve problems of time, speed, and distance, calculate fuel consumption, and make conversions between measurements such as statute and nautical miles. The inner scale on the rotating disk is graduated in hours. The slide rule side also has “windows” that you will use to solve airspeed and altitude problems.
You can see that the number 60 on the rotating disk is marked differently than the other numbers. That is because most of your problems will be concerned with time—“something” per hour, either miles or gallons. Before you get to that, you should learn how to read and interpret the numbers on both portions of the slide rule side.
Rotate the disk until all of the numbers on the middle scale match up with the numbers on the outer scale—10 will be at the top. However, that number “10” may be read as “.1,” “1,” “100,” or “1,000” depending upon the context of the problem . For now, read it as 10. The next number to the right is 11, so each life (or mark) of calibration between the two numbers is equal to .1, and you would read them as 10.1, 10.2, 10.3, etc. If you were solving a problem involving 1,000 pounds of fuel, the number 10 would be read as 1,000, and each calibration would be equal to 10 pounds, and the 11 would be read as 1,100 pounds. See Figure 1.
Now look at the number 15 on the disk. Between 15 and 16 each calibration mark is equal to .2 and would be read as 15.2, 15.4, etc. If you were solving a problem with an airspeed of 150 knots, the first calibration past 15 (150 in this case) would be 152. The spacing changes again at the number 30, where each calibration becomes .5, and at 60, where each calibration equals 1. Before you read a value from the disks, be sure you understand what each line of calibration is equal to.
You will use the slide rule side to establish ratios. With the numbers matched, the ratio is 1 to 1. Now set the number 60 (the rate arrow) directly opposite to (or, “lined-up” with) 12 on the outer disk ( see Figure 2). Notice that all of the numbers on the outer disk are exactly twice the value of the numbers on the inner disk: 90 is opposite of 180, 15 is opposite of 30, 3.5 is opposite of 7.0. You will use these ratios in solving time-speed-distance and fuel consumption problems.
Look at the inside scale on the disk, where the lines of calibration look like clock times: 9:00, 6:00, etc.—these express hours. The inner scale is in hours and the middle scale is in minutes. 1:10 is directly below 70; one hour and ten minutes is the same as seventy minutes. 5:00 is printed below 300 minutes, and five hours is the same as 300 minutes. To convert minutes to seconds, place the rate arrow opposite to the minutes on the outer scale and read seconds opposite to the “seconds” arrow, just to the right of 35 on the inner scale.
The Slide Rule Side
There is no need to be intimidated by the term “circular slide rule.” It simply consists of a rotating disk with numbers in the middle; you set it against the matching numbers on the outer part (the outer scale), and you can work out time, speed, distance, fuel consumption, and conversions between statute miles and nautical miles.
The rotating disk is graduated in hours. The slide rule also has “windows” for solving airspeed and altitude problems.
You will notice that the number 60 is marked differently from the other numbers. That is because almost all of the problems involve (something) per hour, where the something is miles or gallons. Before using it, you need to know how to read it and understand the numbers on both parts of the slide rule side.
Rotate the disk until the numbers in the middle line up with the numbers on the outside. 10 will be at the very top, and depending on the situation that number can be read as ‘0.1’, ‘1’, ‘100’, or ‘1000’. Assuming we read it as 10, the number right next to it on the right will be 11, and between 10 and 11 the calibration marks are in 0.1 units, read as 10.1, 10.2, 10.3, and so on. If you are calculating with 1000 pounds of fuel, the number 10 is read as 1000, and the 0.1-unit marks in between can be read as 10 pounds each. The number 11 can then be read as 1100 pounds. See Figure 1.
Now look at the number 15 on the disk. Between 15 and 16 the marks are spaced 0.2 apart, read as 15.2, 15.4, and so on. If you are calculating with an airspeed of 150 knots, the first mark past 15 (150 in this case) becomes 152. At the number 30 the spacing of the marks changes to 0.5, and at 60 it changes to 1. Before reading a value from the disk, you need to understand which value each line corresponds to.
You need to use the ratios marked on the slide rule side. When the numbers match, the ratio is 1 to 1. Set the inner disk’s (RATE) 60 against 12 on the outer disk (see Figure 2). You can see that every value on the outer disk is twice the value on the inner disk: 180 opposite 90, 30 opposite 15, 7.0 opposite 3.5. You can use these ratios to solve time-speed-distance and fuel consumption problems.
Looking at the inner disk, you can see time marks: 9:00, 6:00, and so on. These represent hours. The inner scale shows hours, and the middle part shows minutes. 1:10 goes under 70; one hour ten minutes equals 70 minutes. 5:00 goes under 300 minutes, and five hours equals 300 minutes. To convert minutes to seconds, set the rate (RATE) against the seconds arrow on the outside. It is located just to the right of 35.
Time, Speed, and Distance Problems
The rate arrow on the disk is always set to indicate a value per hour on the outer scale. There are three basic time-speed-distance problems. In two of these problems you know the rate, while in the third problem, the rate is part of the answer you are looking for.
To find the Time En Route, let’s assume you know your airspeed is 150 knots (nautical miles per hour).
1. Set the rate arrow to 150. See Figure 3.
2. You have determined the distance to your destination to be 245 nautical miles. Speed and distance are always on the outer scale; 245 is halfway between 24 and 25.
3. Look directly opposite to that value on the inner scale to find the Time En Route. It is between 1:35 and 1:40. There are five calibration marks on the middle scale between 1:35 and 1:40, and 245 NM on the outer scale is closest to the third calibration, or one hour and 38 minutes.
To find out how far you can go if your fuel endurance is 4.5 hours and your ground speed is known to be 125 knots:
1. Set the rate arrow at 125 on the outer scale. See Figure 4.
2. Find 4:30 on the inner scale.
3. The value on the outer scale is slightly more than 55. You know that 4 hours at 125 knots should cover 500 miles, so the outer scale is read as 500, not 50 or 5,000, which makes each large calibration mark worth 10 nautical miles. The answer is 564 nautical miles.
In the final and most common type of time-speed-distance problem, the time and distance are known, and you need to solve for unknown speed. The rate arrow represents the answer. You will have flown between two known ground reference points 26 NM apart and checked the time between them to be: 13 (thirteen minutes, that is, not thirteen hours).
1. Set thirteen minutes on the middle scale opposite to 26 on the outer scale. See Figure 5.
2. The rate arrow points to your ground speed, 120 knots.
Try these time-speed-distance problems: (Answers are on Page 37)
|
|
SPEED |
TIME |
DISTANCE |
|
1. |
125 KTS |
? |
524NM |
|
2. |
? |
2:30 |
345 |
|
3. |
110 KTS |
1:40 |
? |
|
4. |
95 |
1:24 |
? |
Time, Speed, and Distance Problems
The RATE (speed) arrow on the disk always points to the per-hour value on the outer disk. There are three basic time, speed, and distance problems. In the two problems before the third one, the known speed is part of the answer.
Let’s assume your flight speed is 150 knots (nautical miles per hour) and find the time en route.
1. Set the RATE arrow to 150. (See Figure 3)
2. Figure the distance to your destination as 245 nautical miles. Speed and distance are always on the outside. 245 is between 24 and 25.
3. To find the time en route, look directly opposite on the inner disk scale; it will be between 1:35 and 1:40, and 245 nautical miles on the outside will be closest to the third mark, or one hour 38 minutes.
Assume the fuel you have gives you 4.5 hours of endurance at most, and that your ground speed is 125 knots:
1. Set the RATE arrow to 125 on the outside. (See Figure 4)
2. Find 4:30 on the inside.
3. The value on the outer scale will be slightly more than 55. You know that 4 hours at 125 knots covers about 500 miles, so that mark should be read as 500, not 50 or 5000. That is because each mark is 10 nautical miles. The answer is 564 nautical miles.
Finally, the most common type of time-speed-distance problem is one where you know the time and distance and solve for the unknown speed. The speed (RATE) arrow shows the answer. Assume you fly 26 nautical miles between two known ground reference points, and when you check the time it is 13 (13 minutes, not 13 hours):
1. Set 13 minutes in the middle against 26 on the outside. (See Figure 5)
2. What the RATE arrow points to is your ground speed: 120 knots.
Solve the following time-speed-distance problems. (Answers are on page 37)
|
|
Speed |
Time |
Distance |
|
1. |
125 knots |
? |
524 nautical miles |
|
2. |
? |
2:30 |
345 nautical miles |
|
3. |
110 knots |
1:40 |
? |
|
4. |
95 knots |
1:24 |
? |
Fuel Consumption Problems
Problems involving fuel consumption, fuel endurance, and fuel capacity are solved using the same numbers you used in the time-speed-distance problems. With the exception of time values, only the names change.
Assume that your airplane’s Approved Flight Manual indicates fuel consumption of 8.4 gallons per hour at a given power setting and that the usable fuel capacity is 64 gallons. How many hours endurance do you have in the tanks?
1. Line up the rate arrow (“something per hour”) with 8.4 on the outer scale. See Figure 6.
2. Now find 64 on the outer scale.
3. Opposite of 64, read fuel endurance in hours: 7:37 on the inner scale. The outer scale, which was used for speed and distance, is now used to indicate gallons per hour and fuel capacity.
When you paid for your fuel you noted on the delivery ticket that it took 32 gallons to top the tanks. You flew four hours and twenty minutes before stopping for fuel. What was the average fuel consumption? This time the rate arrow provides the answer.
1. Set 4:20 on the inner scale (or 260 on the middle scale) opposite of 32 on the outer scale. See Figure 7.
2. The rate arrow indicates the average fuel burn rate: 7.4 gallons per hour.
Remember that fuel consumption is greater during the climb to altitude, so this average value does not accurately reflect fuel consumption in cruising flight.
Try these examples: (Answers are on Page 37)
|
|
GALLONS PER HOUR |
TIME |
TOTAL USED |
|
1. |
7.8 |
3:20 |
? |
|
2. |
? |
4:50 |
62 |
|
3. |
8.5 |
? |
38 |
|
4. |
10 |
2:30 |
? |
|
5. |
12 |
? |
22 |
Fuel Consumption Problems
Problems involving fuel consumption, fuel endurance, and fuel capacity can be solved using the same numbers as the time-speed-distance problems. Except for the time values, only the names change.
Assume the AFM lists fuel consumption as 8.4 gallons per hour and the usable fuel is 64 gallons. How many hours can you keep going on the fuel in the tanks?
1. Place the time (RATE) arrow at 8.4 on the outside. (See Figure 6)
2. Then find 64 on the outside.
3. Opposite 64 you can see the fuel endurance: 7:37. The outside, which used to tell you speed and distance, now tells you gallons per hour and fuel capacity.
Assume that when you paid for fuel, the delivery ticket said 32 gallons were put in, and that you have to fly 4 hours 20 minutes without stopping before the next refueling. What is the average fuel consumption? This time the RATE arrow will give you the answer.
1. Set 4:20 on the inside (or 260 in the middle) opposite 32 on the outside. (See Figure 7)
2. The RATE arrow points to the average fuel consumption: 7.4 gallons per hour.
Since fuel use increases during the climb to altitude, this average cannot be considered exactly the same as the cruise fuel consumption.
Solve the following examples: (Answers are on page 37)
|
|
Gallons per Hour |
Time |
Total Used |
|
1. |
7.8 |
3:20 |
? |
|
2. |
? |
4:50 |
62 |
|
3. |
8.5 |
? |
38 |
|
4. |
10 |
2:30 |
? |
|
5. |
12 |
? |
22 |
Conversions
You can’t solve a problem unless the values agree. You can’t mix statute and nautical miles, gallons and liters, or Fahrenheit and Celsius. Your ASA E6-B Flight Computer makes it possible for you to convert between values with simple settings of the middle scale.
Nautical to Statute Miles
Distances on sectional and world aeronautical charts are in statute miles. Your airspeed indicator usually reads in knots, or nautical miles per hour. It is easy to convert between the two values by using special markings on the slide rule side of your flight computer. Look on the outside scale near 70 for markings labeled NAUT and STAT. Set the known value under the appropriate arrow and read the converted value under the other. For example, to convert 90 knots to statute miles per hour:
1. Set the arrow marked NAUT opposite of 90 on the middle scale.
2. Read 103.5 under the STAT arrow. See Figure 8.
You can convert either nautical or statute miles to kilometers. Find the KM marking on the outer scale. Set the known value beneath the NAUT or STAT arrow as before, and read kilometers under the KM marking. For example, to convert 115 statute miles to kilometers:
1. Set 115 opposite of the STAT arrow.
2. Read 185 under the KM marking. See Figure 9.
Conversions
You probably can’t solve a problem unless the units agree. Statute and nautical miles, gallons and liters, or Fahrenheit and Celsius are examples. The ASA E6-B Flight Computer makes unit conversion possible with a simple setting of the middle scale.
Nautical to Statute Miles
On sectional and world aeronautical charts (WAC), distances are shown in statute miles. Airspeed is read in knots, or nautical miles per hour. Special markings on the slide rule side make converting between these two units easy. Near 70 on the outside you will see the NAUT and STAT markings. Set the known value under the appropriate arrow and read the converted value. For example, let’s convert 90 knots to statute miles per hour.
1. Set the NAUT marking opposite 90 in the middle.
2. Read 103.5 under the STAT arrow. (See Figure 8)
You can also convert statute or nautical miles to kilometers. You can find the KM marking on the outside. As before, put the known value under the NAUT or STAT arrow and read kilometers under the KM marking. For example, let’s convert 115 statute miles to kilometers.
1. Set 115 opposite the STAT arrow.
2. Read 185 under the KM marking. (See Figure 9)
U.S. Gallons to Imperial Gallons
Your Approved Flight Manual lists fuel capacity in U.S. gallons, but in many countries fuel is delivered in Imperial gallons. Arrows marked U.S. GAL and IMP. GAL are provided on both middle and outer scales to help you convert between these quantities. Your tanks are placarded to hold 64 U.S. gallons. How many Imperial gallons will they hold?
1. Line up the U.S. GAL arrow on the middle scale opposite the IMP. GAL arrow on the outer scale.
2. Find 64 on the middle scale.
3. Read 53.2 Imperial gallons on the outer scale ( see Figure 10). Because Imperial gallons are larger than U.S. gallons, the number of U.S. gallons will always be larger.
You have purchased fuel in Canada and the delivery slip says 32 Imperial gallons. How many U.S. gallons have you purchased? Line up the IMP. GAL arrow with the U.S. GAL arrow. Find 32 on the middle scale and read 38.5 U.S. gallons on the outer scale.
U.S. Gallons to Imperial Gallons
The AFM lists fuel quantity in U.S. gallons, but many countries deliver fuel in Imperial gallons. The U.S. GAL and IMP GAL markings are in the middle and on the outside, and they help you convert between these two units. If the fuel tanks hold 64 U.S. gallons, how many Imperial gallons do they hold?
1. Line up the U.S. GAL arrow in the middle with the IMP. GAL arrow on the outside.
2. Find 64 in the middle.
3. Read 53.2 Imperial gallons written on the outside (see Figure 10). Because an Imperial gallon is larger than a U.S. gallon, the U.S. gallon figure is always larger.
Suppose you buy fuel in Canada and the delivery slip says 32 Imperial gallons were delivered. About how many U.S. gallons did you buy? Line up the IMP. GAL arrow with the U.S. GAL arrow, find 32 in the middle, and read 38.5 U.S. gallons on the outside.